Glossar

Machine bearing

A machine bearing is the support of a shaft or spindle within a machine or motor. It guides the rotating component, holds it in position and transfers the forces that occur into the housing or machine frame. In most cases, rolling bearings perform this task.

Functions of a machine bearing

A machine bearing absorbs radial forces perpendicular to the axis of rotation and axial forces along the axis and, depending on the design, tilting moments as well. At the same time, it should guide the shaft with low friction and as little play as possible so that concentricity and positioning accuracy are maintained. Thermal expansion, lubrication and sealing against dirt and moisture are also part of the design.

Typical arrangements

Shafts are often supported at two bearing positions. In a locating/non-locating arrangement, the locating side takes up the axial forces, while the non-locating side compensates for changes in shaft length caused by heat. In an adjusted arrangement, two angular contact ball bearings or tapered roller bearings are preloaded against each other, which increases stiffness. For large, flat axes of rotation such as rotary tables or turntables, a single four-point contact bearing is often sufficient, taking up radial and axial forces and tilting moments at the same time.

Machine bearings with Franke rolling bearings

In Franke wire race bearings, the rolling elements run on inserted race wires instead of solid rings. This means the support can be integrated directly into the surrounding structure, including aluminium, and designed with a large centre clearance, for example for an internal drive. The page Franke principle explains how this works. For very compact bearing positions, slim bearings of type LSA are suitable. Slewing rings with integrated direct drive such as type LTD combine rolling bearing and motor in one housing, so toothed belts, pinions or gearboxes are no longer needed. The glossary entry rolling bearings covers designs and terms.

Franke also manufactures bearings individually to your specifications: Individual bearing program

Frequently asked questions about machine bearings

When is a rolling bearing a better machine bearing than a plain bearing?

A rolling bearing is the better machine bearing compared with a plain bearing when low starting friction, frequent start-stop cycles, changing speeds and precise guidance without clearance are required. Franke wire race bearings also absorb shocks and vibrations through their race rings of hardened spring steel and compensate for slight deformations of the surrounding structure. Plain bearings tend to show their strengths under high shock loads and in steady continuous operation with a stable lubricating film.

How accurate is the radial and axial runout of a machine bearing?

The radial and axial runout of a machine bearing depends, among other things, on its diameter and is largely determined by the surrounding parts, that is the shaft, the housing and their manufacturing accuracy. With Franke wire race bearings, these values can be improved further by a higher manufacturing accuracy of the connecting structure. Standard values are given on the product pages, for example for the bearing element type LEL.

How is the clearance of a machine bearing adjusted?

The clearance of a machine bearing is adjusted via the preload, which seats the rolling elements between the raceways without internal clearance. Franke supplies bearing elements and slewing rings preloaded and free of clearance; on bearing elements the preload can be set individually, while slim bearings are not preloaded and are adapted via ball sorting. Adjustment is made with washers, by solid adjustment or with a threaded ring, as the FAQ on rolling bearings describes.

How much grease does a machine bearing need when it is relubricated?

The relubrication quantity of a machine bearing depends on the calculated free space inside it. For Franke slewing rings, 20 to 30 percent of the calculated volume is filled with lubricant, and 30 to 40 percent for swivel bearings with a swivel angle of up to 90°. The formula is given in the relevant assembly instructions. For initial lubrication Franke uses Shell Gadus S3 V220 C2; the ageing resistance of this lubricant is about three years.

Which materials can a machine bearing be made of?

A machine bearing is usually made of rolling bearing steel, but depending on the application it can also contain corrosion-resistant steel, ceramics or plastic. Franke wire race bearings can have housings of steel, stainless steel, cast iron, aluminium, bronze, plastic or carbon, while the race rings are made of hardened spring steel with typically 52 to 54 HRC. With corrosion-resistant steel, the hardness is 43 to 46 HRC. All combinations are shown in the individual programme for bearings.